waterfiltertested
Buying guide

Whole House Water Filters: What They Do and Do Not Do

Short answerA whole-house filter treats water where it enters your home, but the whole-house systems NSF lists are mainly for chlorine, taste, odor and particulates, plus UV systems and softeners. Check the exact model's listing for the contaminant you care about, and match its rated flow to your peak demand.

By Steffen Hartmann · Last updated

Short answer: a whole-house filter treats all the water that enters your home, which is useful for chlorine taste, sediment and some other problems. It is not a universal fix. The whole-house systems NSF’s consumer guide lists are UV disinfection, softeners and filters for chlorine, taste, odor and particulates. For a health contaminant, the exact model’s certification listing has to say so.

Key facts

  • Definition: CDC says whole-home (point-of-entry) systems treat most or all water entering your home. Point-of-use systems treat water in batches for a single tap, such as the kitchen sink (CDC).
  • Location: NSF says whole-house systems are usually installed near the water meter for municipal water, or at the pressurized storage tank for well water.
  • What NSF lists: whole-house categories on NSF’s consumer page are UV microbiological systems, water softeners and whole-house chlorine filters.
  • Chlorine trade-off: CDC says a whole-home filter that removes chlorine or other disinfectants may let more germs grow in your plumbing.
  • Price range: EPA says filters of all types, including whole-home systems, can cost from as little as $20 to more than $1,000 before maintenance (EPA fact sheet, 2024).
  • Hardness classes (USGS): soft is 0 to 60 mg/L, moderately hard 61 to 120, hard 121 to 180, very hard above 180 mg/L as calcium carbonate.
  • Softener water use: EPA WaterSense says regeneration can use 25 gallons of water or more per day, or up to 10,000 gallons per year.
  • Softener efficiency benchmarks: EPA suggests NSF/ANSI 44 certified models that use 5.0 gallons or less per 1,000 grains of hardness removed, with salt efficiency above 3,350 grains per pound of salt.

Point of entry or point of use

Whole house (point of entry) Under sink or faucet (point of use)
What it treats Every tap, shower and appliance One tap, usually drinking and cooking water
Typical certified claims Chlorine, taste, odor, particulates; UV; hardness (softeners) Can include health claims, such as lead, PFOA and PFOS, through NSF/ANSI 53 or 58, where certified
Installation Plumbed at the main line, near the meter or well tank Under the sink, on the faucet, or in a pitcher
Main benefit Treats bathing, laundry and plumbing too Targets what you drink
Main limit Claims may not cover the contaminant you care about Does not treat other taps

The “typical claims” row is a pattern, not a rule. Certifications belong to individual models. Always read the listing.

What whole-house systems are typically certified for

NSF’s consumer page tells you to check the packaging for both the standard name and a claim for a specific contaminant. CDC describes NSF/ANSI 42 as the taste and odor standard. NSF verifies health-related claims, such as PFOA and PFOS reduction, under NSF/ANSI 53 for general residential filtration devices and NSF/ANSI 58 for reverse osmosis.

In practice that means:

  • Chlorine, taste, odor, sediment: the whole-house filter claims NSF’s consumer page names.
  • Hardness: handled by a softener certified to NSF/ANSI 44, not by a standard filter.
  • Germs: UV systems are a separate NSF category. CDC says UV works better when water is pre-filtered, and that it does not remove chemicals.
  • PFAS, lead, arsenic: do not assume a whole-house unit covers them. EPA says to choose a filter certified to reduce PFAS. CDC says a whole-home filter makes sense when you need a harmful substance, such as certain volatile organic chemicals, removed from all your water, and that you should check the label for what it removes.

If you need PFAS removed at drinking water taps, read our PFAS water filter guide first. A point-of-use system certified for the claim may serve you better than a whole-house unit without it.

How to size a whole-house filter

Sizing is about flow, not household headcount.

  1. Estimate peak demand. List the fixtures that could run at once, such as a shower, a washing machine and a dishwasher. Use the flow ratings on those fixtures, or ask a plumber for a measured figure.
  2. Check rated service flow. Pick a system whose rated service flow, in gallons per minute (gpm), meets or exceeds your peak demand.
  3. Read the pressure drop. Manufacturers publish pressure loss at given flows. A filter that fits on paper can still make showers weak at peak use.
  4. Check capacity. Capacity is how much water the media can treat before replacement. Higher use means more frequent changes.
  5. Check inlet pressure and water source. A well with a pressure tank behaves differently from a city main.

We do not give a single gpm figure here, because it depends on your fixtures, pipe size and pressure. A licensed plumber or water treatment professional can measure it.

Filter versus softener

Whole-house filter Water softener
Main job Removes particles, chlorine or other claimed substances Removes hardness minerals, mainly calcium and magnesium
How it works Depends on media; carbon and sediment are common Cation exchange swaps calcium and magnesium for sodium or potassium (EPA)
Standard NSF/ANSI 42 or 53 for the claims listed NSF/ANSI 44
Removes germs? Only if certified for it No, per CDC
Ongoing needs Cartridge or media replacement Salt, plus regeneration that uses water

CDC adds that some softeners may also reduce iron, manganese, nitrate or arsenic, and tells you to check the label. Minnesota’s Department of Health says softeners are effective on clear-water iron, with 2 to 5 mg/L a more common limit than the up to 10 mg/L some makers report.

Installation and upkeep

Whole-house systems are plumbed into the main line, so most owners hire a plumber or installer. Renters usually need the landlord’s permission, which is one reason many renters choose a point-of-use filter instead.

Upkeep is where cost builds up. NSF tells you to include the ongoing cost of replacement filters in your budget, and CDC says to change filters as the manufacturer recommends, wear gloves, and wash your hands afterward. For softeners, EPA WaterSense says regeneration uses water and salt, so choose a model by both its water and salt efficiency, and keep to the maintenance guidance. Write the install date and the next change date on the unit.

How to check a certificate yourself

  1. Find the certifier and standard on the package. For a filter, look for NSF/ANSI 42, 53 or 58 and a named claim. For a softener, NSF/ANSI 44.
  2. Record the exact model and any replacement cartridge number.
  3. Search the directory. NSF: info.nsf.org/Certified/DWTU. WQA: find.wqa.org/find-products. IAPMO: pld.iapmo.org.
  4. Confirm the claim and the use. The listing should name your contaminant and show that the product is certified for the installation type you plan.
  5. Compare the rated flow and capacity with your sizing figures.
  6. Check the maintenance terms. EPA says filters are effective only if maintained as the manufacturer instructs.

If the model is not listed, treat its claims as unverified.

Do you need one?

Test first. Use your utility’s annual water quality report if you are on city water. Private well owners should have a state-certified lab test the water, because EPA’s rules do not cover private wells. See our well water filter guide.

Two reasons to think twice: whole-house treatment is a larger purchase and a larger maintenance task than a single-tap filter, and a filter that removes chlorine may change the conditions in your pipes, per CDC. If your concern is only drinking water, a certified point-of-use system is usually enough. Our brand checks cover both types.

Questions people ask

Do whole-house water filters remove PFAS, lead or arsenic?

Only if that exact model is certified for it. Whole-house systems commonly carry claims for chlorine, taste, odor and particulates, so look for a PFAS, lead or arsenic claim on the certifier's listing and do not assume it.

What is the difference between a whole-house filter and a water softener?

A filter removes particles or specific contaminants. A cation exchange softener removes hardness minerals, mainly calcium and magnesium, by swapping them for sodium or potassium. Softeners do not remove germs, according to CDC.

How do I size a whole-house water filter?

Match the system's rated service flow, in gallons per minute, to the most water your household uses at the same time, and check the manufacturer's pressure drop at that flow. Total household size matters less than how many fixtures run at once.

Where is a whole-house system installed?

NSF says point-of-entry systems are usually installed near the water meter for city water, or at the pressurized storage tank for well water. Most are placed where the main line enters the home.

Can removing chlorine with a whole-house filter cause problems?

CDC warns that if a whole-home filter removes chlorine or other disinfectants, more germs may grow in your plumbing. Ask your health department or installer if that applies to your setup.

Is a whole-house filter better than an under-sink filter?

Neither is better in general. Whole-house treats every tap, while point-of-use treats one tap. CDC says to consider a point-of-use filter if you only need to treat drinking and cooking water.

How hard is hard water?

USGS classes water as soft at 0 to 60 mg/L, moderately hard at 61 to 120, hard at 121 to 180 and very hard above 180 mg/L as calcium carbonate. A softener, not a standard filter, addresses hardness.

Sources

  1. NSF: Home Water Treatment System and Solutions
  2. CDC: About Home Water Treatment Systems
  3. CDC: About Choosing Home Water Filters
  4. EPA WaterSense: Cation Exchange Water Softeners
  5. EPA WaterSense: Other Water-Efficient Products
  6. USGS: Hardness of Water
  7. EPA: Reducing PFAS in Your Drinking Water with a Home Filter (fact sheet)
  8. NSF: Forever Chemicals and the Advancement of Filtration Standards
  9. Minnesota Department of Health: Iron in Well Water
  10. EPA: Secondary Drinking Water Standards, Guidance for Nuisance Chemicals
  11. WQA: Product Certification (Gold Seal)