waterfiltertested
Buying guide

Well Water Filters: Test First, Then Treat

Short answerTest your well at a state-certified lab before buying any filter, because EPA's public drinking water rules do not apply to private wells and no single filter fixes every problem. Match the treatment to the result: bacteria, nitrate, arsenic, iron, manganese and hardness each call for different equipment.

By Steffen Hartmann · Last updated

Short answer: test first, then treat. If you drink from a private well, you are the one responsible for its safety, and the right filter depends on what a state-certified lab finds. A filter bought before you have results may treat the wrong problem.

Key facts

  • Who relies on wells: around 15 percent of the U.S. population, over 43 million people, use private wells, and EPA estimates more than 23 million households do (EPA Private Drinking Water Wells page).
  • No federal oversight: EPA says private well quality and safety is not regulated by the federal government under the Safe Drinking Water Act, nor by most state governments. CDC says no one monitors or treats private well tap water for you.
  • How often problems appear: a USGS study of 2,100 private wells, cited by EPA, found about one in five had one or more contaminants above a human-health benchmark.
  • Annual tests: CDC and EPA say to test at least once a year for total coliform bacteria, nitrates, total dissolved solids and pH.
  • Nitrate reference level: 10 mg/L as nitrogen is EPA’s limit for public water (EPA National Primary Drinking Water Regulations).
  • Arsenic reference level: 0.010 mg/L (10 µg/L), the EPA limit for public water (EPA).
  • Nuisance levels: EPA’s secondary guidelines are 0.3 mg/L for iron, 0.05 mg/L for manganese and 500 mg/L for total dissolved solids, with a pH range of 6.5 to 8.5. These relate to taste, staining and appearance.
  • PFAS and UCMR data: EPA’s 2024 PFAS rule and its UCMR 5 monitoring (29 PFAS, 2023 to 2025, dataset released August 2026) cover public water systems. A private well appears in neither unless you test it.

Why wells are different

City water gets routine testing and a yearly report. A private well has no such system. EPA’s drinking water standards are written for public water systems, so for a well they act as reference points, not as enforced limits. Contamination can come from your own septic system, nearby farms, old fuel tanks or natural geology.

Because EPA’s rules do not reach you, the national data you may have seen about PFAS and other contaminants does not describe your water. The only data about your well is the data you collect.

Step 1: test the water

Follow these steps before you shop:

  1. Ask your health department what to test for. CDC says the right tests depend on where your well is, your state or region, and whether the area is rural or urban.
  2. Use a state-certified laboratory. EPA says to use only labs certified for drinking water testing. Your local health department may offer well testing, sometimes free, and EPA keeps a page listing state certification programs.
  3. Start with the annual basics: total coliform, nitrate, total dissolved solids and pH. Add arsenic at least once (Minnesota’s health department recommends this), plus any local concern such as lead, radium, volatile organic compounds, or PFAS.
  4. Test again after any change: flooding, repairs, new construction or industrial activity nearby, or a change in taste, color or smell (EPA, CDC).
  5. Keep the report. It is the document you will match against filter listings.

Step 2: match treatment to the problem

Problem Reference level What you may notice Treatment options to discuss (check certification)
Coliform bacteria or E. coli Indicator of possible contamination (CDC) Often nothing Disinfection, such as chlorine, ozone or ultraviolet light (EPA); retest after
Nitrate 10 mg/L as nitrogen Nothing Reverse osmosis or distillation (CDC); never boiling
Arsenic 10 µg/L Nothing Reverse osmosis, distillation, oxidation filtration, or chlorination and filtration (Minnesota Department of Health)
Iron 0.3 mg/L Rust stains, metallic taste Softener or iron filter; aeration or oxidation at higher levels
Manganese 0.05 mg/L Black or brown staining, bitter metallic taste Aeration, or coagulation and filtration (EPA)
Hardness USGS: above 180 mg/L is very hard Scale, poor soap lather Cation exchange softener (CDC)

Every row is a starting point for a conversation with a water treatment professional or your health department. None of it replaces a certified claim for the exact product.

Bacteria

CDC says that if your well contains harmful germs, you should not drink the water, and should use bottled or other safe water until the well is treated and a retest confirms the fix. CDC also says microfiltration is only somewhat effective on bacteria and does not remove viruses, and that UV systems work better when water is pre-filtered. A kitchen carbon filter is not a disinfection plan.

Nitrate and arsenic

Neither has a taste or smell, so only a test finds them. Minnesota’s health department says water above 10 mg/L nitrate can cause immediate health problems, and that bottle-fed babies under six months face the highest risk. For arsenic, it recommends action above 10 µg/L and says even low levels over many years are associated with increased cancer risk. Choose a unit certified by an independent body, and retest the treated water.

Iron and manganese

Iron above 0.3 mg/L is usually objectionable, according to Minnesota’s health department. Softeners and iron filters handle clear-water iron within limits: 2 to 5 mg/L is a more common limit for softeners, and up to 10 to 15 mg/L for a manganese greensand filter. Higher levels may call for aeration or chemical oxidation, followed by filtration. Iron can plug reverse osmosis units, so a whole-house system may suit better. Our whole house water filter guide covers sizing.

Hardness

Hard water is mostly a scale and soap problem. CDC says softeners remove calcium and magnesium, and that some also reduce iron, manganese, nitrate or arsenic, depending on the label. Softeners do not remove germs.

Order matters

Equipment often works in stages. Sediment or iron treatment typically comes first to protect downstream parts, then any disinfection or point-of-use treatment such as reverse osmosis at the kitchen tap. A professional should design the sequence for your results.

Protect the well itself

Treatment equipment is the last line of defense. EPA’s well owner guidance also lists steps that reduce contamination at the source:

  • Slope the ground around the well so surface runoff drains away.
  • Install a well cap or sanitary seal.
  • Keep records of well maintenance, including any disinfection.
  • Hire a certified well driller for new construction, changes or closure.
  • Keep pesticides, fertilizers, fuels and degreasers away from the well, and pump and inspect your septic system as your local health department recommends.

CDC adds that you should check your well every spring for mechanical problems.

How to check a certificate yourself

  1. Start from your lab report, not the product page. Note each contaminant and its level.
  2. Find the standard and certifier on the package. For drinking water filters, NSF/ANSI 53 (health claims) and 58 (reverse osmosis) are the usual marks. UV microbiological systems and softeners are separate NSF categories.
  3. Copy the exact model number and search the certifier’s directory: NSF at info.nsf.org/Certified/DWTU, WQA at find.wqa.org/find-products, or IAPMO at pld.iapmo.org.
  4. Confirm the listing names your contaminant. A general NSF mark is not enough. CDC says to check that the system removes the type of germ or chemical you are concerned about.
  5. Check the limits. A listing tests a specific challenge level. If your result is far higher, ask the maker or installer.
  6. Retest after installation. CDC says to test the water to make sure treatment worked.

What to do next

Order the lab test, keep the report, and treat only what it shows. Check back for our brand checks, which review certification listings rather than marketing claims.

Questions people ask

Do I need a filter for well water?

Not until you test. CDC and EPA say to test your well at least once a year for total coliform bacteria, nitrates, total dissolved solids and pH, and to ask your health department what else to test for in your area.

Does EPA regulate private well water?

No. EPA says the quality and safety of private domestic wells is not regulated by the federal government under the Safe Drinking Water Act, nor by most state governments. The owner is responsible for testing and treatment.

How often should I test my private well?

At least once a year for the basics, and also after flooding, nearby land disturbance, repairs to the well system, or a change in taste, color or smell. CDC adds pregnancy and a new child in the home as reasons to test.

Can a filter make bacteria-contaminated well water safe?

Do not rely on a filter alone. CDC says to avoid drinking well water that contains harmful germs, use bottled or other safe water, have the well treated, and test again to confirm. EPA lists chlorine, ozone and ultraviolet light as disinfection options.

What removes iron and manganese from well water?

For iron, Minnesota's Department of Health says softeners and iron filters work on clear-water iron within limits, and aeration or chemical oxidation with filtration is used at higher levels. EPA says aeration and coagulation with filtration remove iron and manganese.

Will boiling remove nitrate or arsenic?

No. CDC says boiling does not remove chemicals, and Minnesota's Department of Health warns that boiling makes nitrate more concentrated. Treatment such as reverse osmosis or distillation is needed, and the product must be certified for the contaminant.

Where do I find a state-certified lab?

Your state or local health department can send you a list of certified labs, and some offer testing. EPA keeps a page with contact information for state certification programs and certified drinking water laboratories.

Sources

  1. EPA: Private Drinking Water Wells
  2. EPA: Protect Your Home's Water
  3. EPA: Contact Information for Certification Programs and Certified Laboratories for Drinking Water
  4. CDC: Guidelines for Testing Well Water
  5. CDC: Guidelines for Treating Well Water
  6. CDC: About Home Water Treatment Systems
  7. EPA: National Primary Drinking Water Regulations
  8. EPA: Secondary Drinking Water Standards, Guidance for Nuisance Chemicals
  9. EPA: Final PFAS National Primary Drinking Water Regulation
  10. EPA: Fifth Unregulated Contaminant Monitoring Rule (UCMR 5)
  11. Minnesota Department of Health: Nitrate in Well Water
  12. Minnesota Department of Health: Arsenic in Well Water
  13. Minnesota Department of Health: Iron in Well Water
  14. USGS: Hardness of Water